[plesi]

Není potřeba...testováno na x96mini
SSH:root/coreelec

Kód:

##############################################
#                  CoreELEC                  #
#            https://coreelec.org            #
##############################################

CoreELEC (official): 9.0.1 (Amlogic.arm)
CoreELEC:~ # dmesg | grep -i usb
[    0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,576cvbs maxcpus=4 vout=576cvbs,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=c4:4e:ac:20:86:61 androidboot.mac=c4:4e:ac:20:86:61 androidboot.slot_suffix=_a bootfromusb console=tty0 systemd.show_status=auto ssh
[    0.320783@0] usbcore: registered new interface driver usbfs
[    0.320879@0] usbcore: registered new interface driver hub
[    0.320996@0] usbcore: registered new device driver usb
[    0.392434@1] usbcore: registered new interface driver smsc95xx
[    0.392975@1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.393240@1] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.393561@1] usbcore: registered new interface driver usb-storage
[    0.393792@1] usbcore: registered new interface driver usbserial
[    0.393892@1] usbcore: registered new interface driver usbserial_generic
[    0.393980@1] usbserial: USB Serial support registered for generic
[    0.394073@1] usbcore: registered new interface driver pl2303
[    0.394153@1] usbserial: USB Serial support registered for pl2303
[    0.394754@1] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000ee000
[    0.394988@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[    0.395018@1] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000fa080
[    0.399993@1] usbcore: registered new interface driver usbhid
[    0.400019@1] usbhid: USB HID core driver
[    4.623373@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    4.637276@3] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.644099@3] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.651402@3] usb usb1: Product: xHCI Host Controller
[    4.656392@3] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
[    4.662005@3] usb usb1: SerialNumber: xhci-hcd.0.auto
[    4.667701@3] hub 1-0:1.0: USB hub found
[    4.680665@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    4.688517@1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    4.695291@1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.702629@1] usb usb2: Product: xHCI Host Controller
[    4.707625@1] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
[    4.713240@1] usb usb2: SerialNumber: xhci-hcd.0.auto
[    4.718833@3] hub 2-0:1.0: USB hub found
[    4.998179@1] usb 1-1: new full-speed USB device number 2 using xhci-hcd
[    5.138894@0] usb 1-1: New USB device found, idVendor=0a05, idProduct=7211
[    5.138898@0] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    5.138901@0] usb 1-1: Product: USB2.0 HUB
[    5.139345@3] usb 1-1: ep 0x81 - rounding interval to 1024 microframes, ep desc says 2040 microframes
[    5.200945@3] hub 1-1:1.0: USB hub found
[    5.215186@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[    5.215203@2] dwc_otg_driver_probe host only, not probe usb_otg!!!
[    5.328171@0] usb 1-2: new high-speed USB device number 3 using xhci-hcd
[    5.468831@0] usb 1-2: New USB device found, idVendor=14cd, idProduct=1212
[    5.468845@0] usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[    5.468852@0] usb 1-2: Product: Mass Storage Device
[    5.468857@0] usb 1-2: Manufacturer: Generic
[    5.468863@0] usb 1-2: SerialNumber: 121220160204
[    5.470530@1] usb-storage 1-2:1.0: USB Mass Storage device detected
[    5.471226@1] scsi0 : usb-storage 1-2:1.0
[    5.708459@3] usb 1-1.1: new low-speed USB device number 4 using xhci-hcd
[    5.814779@3] usb 1-1.1: New USB device found, idVendor=0e8f, idProduct=00fb
[    5.814879@3] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.814951@3] usb 1-1.1: Product: USB Mouse
[    5.815017@3] usb 1-1.1: Manufacturer: YSTEK
[    5.819656@1] usb 1-1.1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[    5.854903@3] input: YSTEK USB Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:0E8F:00FB.0001/input/input2
[    5.859272@3] hid-generic 0003:0E8F:00FB.0001: input,hidraw0: USB HID v1.10 Mouse [YSTEK USB Mouse] on usb-xhci-hcd.0.auto-1.1/input0
[    6.098543@3] usb 1-1.2: new low-speed USB device number 5 using xhci-hcd
[    6.220945@3] usb 1-1.2: New USB device found, idVendor=04d9, idProduct=a01c
[    6.221043@3] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.221114@3] usb 1-1.2: Product: Wireless USB Device
[    6.221182@3] usb 1-1.2: Manufacturer: HOLTEK
[    6.225009@1] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[    6.225577@1] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[    6.411295@1] input: HOLTEK Wireless USB Device as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.0/0003:04D9:A01C.0002/input/input3
[    6.414418@3] hid-generic 0003:04D9:A01C.0002: input,hidraw1: USB HID v1.10 Keyboard [HOLTEK Wireless USB Device] on usb-xhci-hcd.0.auto-1.2/input0
[    6.451770@3] input: HOLTEK Wireless USB Device as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.1/0003:04D9:A01C.0003/input/input4
[    6.455861@3] hid-generic 0003:04D9:A01C.0003: input,hidraw2: USB HID v1.10 Mouse [HOLTEK Wireless USB Device] on usb-xhci-hcd.0.auto-1.2/input1
[    6.688141@0] usb 1-1.3: new full-speed USB device number 6 using xhci-hcd
[    6.788481@3] usb 1-1.3: No LPM exit latency info found.  Power management will be impacted.
[    6.788598@3] usb 1-1.3: not running at top speed; connect to a high speed hub
[    6.923528@3] usb 1-1.3: New USB device found, idVendor=148f, idProduct=7601
[    6.923544@3] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    6.923551@3] usb 1-1.3: Product: 802.11 n WLAN
[    6.923556@3] usb 1-1.3: SerialNumber: 1.0
[    7.158121@3] usb 1-1.4: new full-speed USB device number 7 using xhci-hcd
[    7.258208@3] usb 1-1.4: not running at top speed; connect to a high speed hub
[    7.258537@3] usb 1-1.4: unable to read config index 0 descriptor/start: -61
[    7.258545@3] usb 1-1.4: can't read configurations, error -61
[    7.338089@3] usb 1-1.4: new full-speed USB device number 8 using xhci-hcd
[    7.438203@3] usb 1-1.4: not running at top speed; connect to a high speed hub
[    7.438485@3] usb 1-1.4: unable to read config index 0 descriptor/start: -61
[    7.438492@3] usb 1-1.4: can't read configurations, error -61
[    7.518082@1] usb 1-1.4: new full-speed USB device number 9 using xhci-hcd
[    7.538276@1] usb 1-1.4: not running at top speed; connect to a high speed hub
[    7.538573@1] usb 1-1.4: unable to read config index 0 descriptor/start: -61
[    7.538579@1] usb 1-1.4: can't read configurations, error -61
[    7.618082@2] usb 1-1.4: new full-speed USB device number 10 using xhci-hcd
[    7.638277@2] usb 1-1.4: not running at top speed; connect to a high speed hub
[    7.638566@2] usb 1-1.4: unable to read config index 0 descriptor/start: -61
[    7.638573@2] usb 1-1.4: can't read configurations, error -61
[    7.638644@2] hub 1-1:1.0: unable to enumerate USB device on port 4
[   33.405207@0] rtusb init rt2870 --->
[   33.509214@0] usbcore: registered new interface driver rt2870
[  204.569334@2] usb 1-1: USB disconnect, device number 2
[  204.569365@2] usb 1-1.1: USB disconnect, device number 4
[  204.930227@3] usb 1-1.2: USB disconnect, device number 5
[  205.470148@2] usb 1-1.3: USB disconnect, device number 6
[  210.369792@1] usb 1-1: new high-speed USB device number 11 using xhci-hcd
[  210.510262@1] usb 1-1: New USB device found, idVendor=0572, idProduct=c689
[  210.510280@1] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  210.510287@1] usb 1-1: Product: EyeTV Stick
[  210.510292@1] usb 1-1: Manufacturer: Geniatech
[  210.510298@1] usb 1-1: SerialNumber: 160421
[  210.544480@2] dvb-usb: found a 'Mygica T230C DVB-T/T2/C' in warm state.
[  210.790501@2] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  210.796403@2] usb 1-1: media controller created
[  210.828232@2] usb 1-1: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[  210.860159@2] rc rc1: Mygica T230C DVB-T/T2/C as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/rc/rc1
[  210.860525@2] input: Mygica T230C DVB-T/T2/C as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/rc/rc1/input7
[  210.861195@2] rc rc1: lirc_dev: driver dvb_usb_cxusb registered at minor = 1, scancode receiver, no transmitter
[  210.861213@2] dvb-usb: schedule remote query interval to 100 msecs.
[  210.861310@2] dvb-usb: Mygica T230C DVB-T/T2/C successfully initialized and connected.
[  210.861574@2] usbcore: registered new interface driver dvb_usb_cxusb
[  212.917049@2] usb 1-1: DVB: adapter 0 frontend 0 frequency 0 out of range (42000000..870000000)
CoreELEC:~ #

Doplňky:
"Drivers-CoreElec Module Drivers" najdeš pod "Doplňky programů" (stačí vybrat druhou volbu- DVB drivers for TBS)

Služby-Tvheadend Server 4.2